— Gas & pressure calculator

Which gas, what pressure, how much?

Tell us what is going in your keg and how cold it is. You get the gas to use, the number to set on your regulator and how much gas to have ready.

Is it fizzy already?
How fizzy do you like it?
How strong is the mix?
Use the temperature of the liquid itself. A keg that went into the fridge an hour ago is still warm inside.
3How big is your keg?
L
Fine-tune for your setup
What gas supply do you have?
Which kind of keg?
How will the keg sit?
    How to do it, step by step

      Regulator off first. Wind the regulator knob all the way anticlockwise before you fit or remove a bulb or bottle, and before you connect to or disconnect from the keg.
      — Troubleshooting

      Something not right?

      Nearly every problem comes down to temperature, pressure, gas or a connection. Check your keg below, or open the problem that matches.

      Check your keg right now
      This works for drinks on CO₂. It uses the drink you picked in the calculator above.
      It pours all foam

      Taste it first. That tells you which way to go.

      • Foamy and tastes flat: it is under-carbonated. Leave it a day at the pressure from the calculator.
      • Foamy and very fizzy: it is over-carbonated. Turn the regulator off, pull the ring to let pressure out, wait an hour and repeat. Then set the calculator pressure.
      • Drink, keg or glass too warm: chill the keg and rinse the glass with cold water.
      • Pressure too high while pouring: wind down to about 10 psi to pour, then back up to store.
      • Just filled or just carried: let it rest for 30 minutes.
      • First pour of the day: run the first splash off. Pouring onto foam makes more foam.
      It pours flat
      • Pressure too low for the temperature: a warmer drink needs more pressure. Check your numbers in the calculator above.
      • Not enough time: a flat drink needs shaking, or a few days at pressure, before it is fizzy.
      • Wrong gas: only CO₂ makes fizz. Nitrogen and nitrous oxide will not carbonate a drink.
      • Gas ran out: if the needle has dropped, the bulb is empty. Regulator off, new bulb, back up to pressure.
      • Stored without pressure: a fizzy drink left at low pressure slowly loses its fizz into the empty space.
      Nothing comes out
      • No pressure: check the needle. At zero, the regulator is off or the bulb is empty.
      • Button locked: take the locking clip off the button.
      • Dip tube: check it is pushed on, not kinked, and not jammed flat against the bottom of the keg. Trim it a little if it is.
      • Blocked: pulp, coffee grounds, seeds or herbs clog the tap. Strain the drink and rinse the tap through with warm water.
      • Connections: push the gas disconnect on until it clicks.
      Only gas comes out with the keg lying down

      The dip tube is wedged against the keg base on the high side, so it sits in gas and not in drink. Spin the keg until the tube drops back into the liquid, or cut the tube slightly shorter so it cannot jam. Always fit the check valve when the keg lies down. It stops drink running back into the regulator.

      My gas runs out too fast
      • Find the leak: turn the regulator off, then brush soapy water around the bulb, regulator and fittings. Bubbles show where gas escapes.
      • Fix it: re-seat or replace the o-ring there and add a little keg lubricant.
      • Lots of empty space: a half-empty keg uses extra gas just to fill the space. Match the keg to the batch.
      • Carbonating from flat: this uses far more gas than pouring a drink that is already fizzy. The calculator shows how much.
      The button is stiff or the pour is hard to control

      The pressure is too high for pouring. Above 20 psi the button gets hard to press. Wind down to about 10 psi, hook a finger under the spout and press the button with your thumb. Start gently and press harder for a faster flow. The first press of a round can stick for a moment. Go back to your storage pressure when you are done.

      My nitro drink has no creamy head
      • Not cold enough: the drink has to be close to 0 °C before the gas goes in. Chill every ingredient and keep the ice in the recipe.
      • Pressure too low: infuse at 45 psi or more, then drop to about 20 psi to pour.
      • Not shaken: shake hard for 30 seconds, like a cocktail shaker.
      • Too much alcohol: strong mixes will not hold foam. Add more coffee, use Wonderfoam, and shake again.
      • The coffee: some coffees do not foam. A strong cold brew concentrate or espresso works best.
      The gauge does not match what I expect

      With the check valve fitted, the gauge shows the pressure between the regulator and the valve, not inside the keg. If the keg warms up, the pressure inside rises and the gauge will not show it. Use the check valve when the keg lies down and take it out when it stands up if you want an exact reading.

      The needle is stuck and will not go back to zero

      This usually happens after gas was fitted or removed while the regulator was still turned on. The jolt can shift where the needle rests. To find out whether the regulator still works:

      • Take the check valve out of the regulator. With it in, pressure from the keg cannot reach the gauge.
      • Turn the regulator off and connect it to a keg that already has pressure in it.
      • Watch the needle. If it moves up from where it was resting, the gauge is working. It just has a new zero, so count your pressure from that resting point.
      • If it does not move at all, get in touch with us and send a photo of the gauge.

      Pressures come from the standard brewing carbonation chart: the colder the drink, the less pressure it needs for the same fizz. Gas amounts are estimates that include filling the keg, pushing the drink out and a little lost when you change bulbs. Taste as you go and adjust by 1 to 2 psi to suit yourself.

      Your keg's safety valve opens at 75 psi. This guide never asks you to go above 50 psi.